EICA Crane Certification Practice Test

These questions are part of the practice quiz. Start practicing

• What characterizes a rough terrain crane?
• What is the primary purpose of installing a boom extension on a crane?
• Which of the following is crucial for preventing overload situations in cranes?
• Who is responsible for conducting annual crane inspections?
• Which device would typically not be involved in limiting the boom movement of a crane?
• What is a boom tip platform?
• What is the minimum diameter of the qualified electrical worker’s tool for 13kV?
• Which condition is NOT a factor of ground condition related to crane operation?
• Which standard is recognized for its guidelines on hand signal charts?
• What does NESC stand for?
• Why is monitoring the percentage of slope important in crane operations?
• Which table is referenced for determining minimum clearances while traveling under energized power lines?
• Which of the following is NOT a responsibility of the crane operator?
• What is the purpose of "storing" a crane jib?
• Why is a hoist hook critical in crane operations?
• What must be included in the assessment of job site hazards before crane operations commence?
• Which of the following is required safety equipment?
• How is a crane defined in construction?
• Who must check repairs or resolution checks on crane equipment?
• How many crew members need to be trained in First Aid / CPR when working in remote areas?
• Before transport, how should the A2B device be positioned?
• What is a Kelly Bar used for?
• Which type of crane is specifically designed for highway travel?
• What does LMI stand for in crane operation context?
• What is the minimum distance recommended from a 12kV line while traveling?
• What does OSHA 1926 primarily address?
• What does the acronym DVIR stand for?
• Which standard addresses the specifications for hooks?
• Which of the following describes a sheave's function?
• How often are periodic crane inspections performed?
• If a crane contacts a powerline, what is the first action you should take?
• At what temperature does polypropylene rope begin to melt?
• To ensure safety and compliance, periodic crane inspections must be performed by whom?
• What is the primary use of a hoist hook in crane operations?
• What is the function of an LMI (load moment indicator) in crane operation?
• During lifting operations, what should be monitored regarding the crane's drum?
• What diagram provides information about working quadrants?
• What is the function of the A2B device on a crane?
• Who is responsible for completing daily DOT inspection forms for crane operation?
• What does ASME B30.26 focus on?
• Lifting over the corner with a crawler crane produces what?
• What is the typical stability percentage of a crane operating on rubber?
• What function does a counterweight serve in crane operations?
• How much is 1% of level at 4 feet?
• What is the purpose of a lift plan in crane operations?
• What is required for equipment operating on rails?
• What is prohibited under outrigger beams?
• ASME B30.23 provides guidelines for which type of systems?
• What is the primary focus of ASME B30.10?
• What's the consequence of not complying with OSHA retraining requirements?
• What is the purpose of matting in crane operations?
• What is the minimum swing clearance required for a crane's boom and counterweights?
• Which standard pertains specifically to cranes in construction according to OSHA regulations?
• What safety measure should be taken when preparing to lift personnel?
• What action should be taken if a crane is near unidentified underground obstructions?
• How does a counterweight enhance the safety of crane operations?
• What is required for crane operators every three years?
• Which of the following describes a person who has demonstrated the ability to solve or prevent problems in their field?
• Before a crane enters a jobsite, what must be addressed?
• Which level of safety does OSHA 1926 apply to?
• What is the purpose of the personnel platform proof test?
• What qualifies a person as a 'qualified person' in crane operations?
• What is the maximum wind speed for crane operation with a man basket installed?
• Which ASME standard relates to rigging hardware?
• What is used when RT crane outriggers are not fully extended?
• When picking from rubber tires, what should be checked?
• What is the minimum distance a crane operator should stay from the edge of a slope?
• Which ASME standard pertains to mobile hydraulic cranes?
• What does the acronym ASME stand for?
• How often is retraining required by OSHA if a task has not been completed?
• What is a lattice boom?
• What is the frequency of annual crane inspections?
• What is the primary mechanism for raising, lowering, extending, and retracting a hydraulic boom?
• Which limiting device helps in controlling the angle of the boom?
• How does the size of the crane winch drum affect its performance?
• Who is responsible for maintaining steps, handrails, ladders, etc., on a crane?
• What is the main boom angle when installing a jib on a crane?
• What is the consequence of not checking repairs or resolution on cranes?
• For rotation resistant wire rope inspection, how many random wires are needed in 30 rope diameters?
• ASME B30.5 is the standard that applies to which type of cranes?
• Which type of cranes is OSHA 1910.180 concerned with?
• What is a rejection criterion for standing rope?
• What does an activated anti-2 block prevent during crane operation?
• What is the weight that cannot be exceeded when lifting personnel?
• What does the term "floats" refer to in crane operations?
• Which indicator helps in assessing the length of the boom?
• What device is used to limit the hoisting operation on a crane?
• What measurement is crucial for safety in crane operations and determines the effectiveness of the setup?
• What is the maximum period a crane can go without an inspection by a qualified person?
• What distinguishes an all terrain crane?
• What is the primary focus of NESC rules?
• What is the minimum number of wraps required on a crane drum?
• What is the minimum approach distance for cranes when working with unqualified electrical workers?
• What is the maximum acceptable slope for a digger derrick setup?
• What does a lift plan document?
• How many random wires are needed for rotation resistant wire rope inspection criteria in 6 rope diameters?
• What is an outrigger used for?
• What does ASME B30.9 standardize?
• What is required during a personnel platform preflight test?
• What is the minimum approach distance for cranes designed for qualified electrical workers according to OSHA?
• Which items are checked first in a DVIR?
• What is the purpose of maintaining DOT inspection forms daily?
• Which component of a crane is typically hydraulically operated and located at the front?
• What happens when the boom of an unlevel crane is swung to the low side?
• What is the primary reason for lubricating wire rope?
• What is the purpose of the A2B (anti two block) device?
• What is the function of the FMCSA?
• Who determines the maximum wind speed a crane can safely operate in?
• What aspect of crane operation does ASME B30.15 specifically cover?
• Why is it important to secure the A2B device during transport?
• How often should crane operators be recertified to maintain safety standards?
• What type of equipment is typically required when a crane operation involves a high-risk approach to electrical lines?
• What is an essential qualification for a competent person as per OSHA?
• Which of the following is classified as an underground obstruction?
• What is the typical stability percentage of a crane operating on outriggers?
• What must all employees be trained and qualified in, according to safety standards?
• What must slings used to hoist personnel include?
• What does a block hook consist of?
• What is a defining feature of the crawler crane's tracks?
• What effect do screw-in anchors have on a digger boom?
• What does it mean when a crane jib is "stowed"?
• What mechanism is crucial for ensuring safe lifting operations in cranes?
• Which of the following is true about a boom hoist limiting device?
• What should the operator do first during a crane powerline contact situation?
• What type of crane uses a lattice design to provide strength and reduce weight?
• What role does OSHA play in workplace safety?
• What defines a crawler crane?
• What does OSHA require when leaving a hole open?
• What aspect of crane performance does stability refer to?
• What does the term "qualified person" refer to in crane operations?
• What does a crawler crane generally use for lifting heavy objects?
• Lifting over the side with a crawler crane produces ____ ground pressure.
• Why is it important not to exceed 50% of rated capacity when lifting personnel?
• What is the minimum size requirement for outrigger pads?
• What does structural competence in a crane refer to?
• What is one major consequence of not adhering to crane stability guidelines?
• Which of the following is required to recertify for EICA?
• Which indicator provides information about the load radius in crane operations?
• According to OSHA, what defines a competent person?
• OSHA 1926.1422 is specifically related to which aspect of crane operations?
• What factor does swinging an unlevel crane to the low side affect most?
• When considering safety measures, how far should operators stay from the edge of a slope?
• How long is EICA certification valid?
• What should be done to the overhaul ball before transporting a crane?
• What is the formula to calculate the percentage of slope?
• Which safety device is essential for cranes?
• Before transporting a crane, what must be done with the overhaul ball?
• When do crawler cranes exert the greatest ground force?
• What is necessary for crawler cranes operating on unstable ground?
• What effect does boom deflection have on load radius?
• At what wind speed should a qualified person determine the safety of crane operations?
• Before transporting a crane, what must be done to the boom?
• What is a primary function of the radius indicator in crane operation?
• Which organization is responsible for setting safety standards in mechanical engineering?
• What does ASME P30.1 provide guidelines for?
• In crane operations, which device indicates the maximum height to which a load can be lifted?
• What is the main purpose of conducting a drift check during hydraulic line inspections?
• How often is a personnel platform proof test required?
• Which material should be avoided when heat and friction are a concern?
• At what elevation does the MAD table altitude factor begin?
• What is the correct location to level a crane using a 4-foot level?
• What is NOT a consideration when ensuring crane stability?
• When setting up a crane, what is the first step to achieve proper leveling?
• What does FACE stand for in the context of crane safety?
• For unknown voltage situations, what is the minimum distance a worker should maintain?
• Which type of crane would be most suitable for a construction site with very uneven terrain?
• What is required before a toolbox installation on a crane can occur?
• What is the main advantage of a hydraulic boom crane?
• What are outrigger pads considered as?
• What must equipment with a foot pedal brake have?
• What is required to be filled out when a crane is to be driven on a public road?
• In terms of crane safety, what is the maximum wind gust speed typically allowed for operations to continue?
• What is the requirement for cribbing when using a crane?
• Which device is primarily used to prevent two-blocking in crane operations?
• What is the primary purpose of the Fatality Assessment and Control Evaluation program?
• Which component is critical in the installation sequence of a lattice boom pin assembly?
• What is the minimum number of wires required for running rope inspection criteria?
• What is the focus of OSHA 1910 regulations?
• What is the primary purpose of a range diagram in crane operations?
• What is the maximum acceptable slope for setting up a crane?
• What is essential for planning load handling activities according to ASME guidelines?
• What immediate action should be taken if a crane has a leak?
• What is a necessary feature for hydraulic outrigger jacks?
• Which factors determine the ground condition for crane operation?
• A dedicated spotter or signalperson is required when which of the following conditions exist?
• To what precision should cranes be leveled?
• What does load radius refer to in crane operation?
• In what order should the lattice boom pin assembly be installed?
• What does OSHA 1926.1431 specifically apply to?
• What is a sheave in the context of crane operation?
• What does OSHA 1926.1408 Table A help determine?
• What is the minimum clearance required for non-qualified workers near 50-200kV lines?
• What is a drift check used for in hydraulic line inspection?